擠塑板是一種保溫性能較好的板材，但是在施工后期出現操作失誤需要補救時，應該如何處理呢？另外，存放時要注意什么？下面來講講吧。

Extruded board is a kind of board with good thermal insulation performance, but what should be done when there are operational errors that need to be remedied in the later stage of construction? In addition, what should we pay attention to when storing? Let's talk about it.

擠塑板問題的補救措施

Remedial measures for extrusion plate problems

先找出不合格的板材，再選擇全新的板材。根據這批不合格的尺寸，裁切后，在新裁切的背面涂上油漆和粘合劑，然后在需要修補的地方貼上不粘貼紙。膠，以免灰塵污染，然后用水或刷子清潔表面，然后在新的擠壓板上涂膠。準備一塊比修復面小的網布，保證網布寬度大于8cm，涂層要均勻涂布，無褶皺。擠出片材通常具有很好的穩定性。

Find out the unqualified plates first, and then select the brand-new plates. According to this batch of unqualified sizes, after cutting, paint and adhesive shall be applied on the back of the new cutting, and then non stick stickers shall be pasted on the places that need to be repaired. Glue to avoid dust pollution, then clean the surface with water or brush, and then apply glue on the new extrusion plate. Prepare a piece of mesh smaller than the repair surface to ensure that the mesh width is greater than 8cm, and the coating should be evenly coated without wrinkles. Extruded sheets usually have good stability.

如果施工后發現一小部分材料出現異常，這個時候我們千萬不要慌張，因為我們不是不可逆轉的，我們還是可以彌補的。修復之后，甚至我們的效果都比之前好，但是修復之后的效果不如我們剛開始的時候，所以我們的效果并不理想。

If a small part of materials are found abnormal after construction, we must not panic at this time, because we are not irreversible, and we can still make up for it. After the repair, even our effect is better than before, but the effect after the repair is not as good as when we first started, so our effect is not ideal.

擠塑板問題的解決方法及注意事項

Solutions and precautions for extrusion plate problems

擠塑聚苯乙烯在建筑行業的應用非常普遍。該產品具有抗壓強度高、抗沖擊能力強的優點。根據XPS的不同型號和厚度，其抗壓強度達到150~700kpa以上，可以承受各種系統的地面荷載。廣泛應用于地熱工程、高速公路、機場跑道、廣場地面、大型冷庫、室內裝飾保溫等領域。

Extruded polystyrene is widely used in construction industry. The product has the advantages of high compressive strength and strong impact resistance. According to different models and thicknesses of XPS, its compressive strength can reach more than 150~700kpa and can bear the ground load of various systems. It is widely used in Geothermal Engineering, expressway, airport runway, square ground, large cold storage, indoor decoration and thermal insulation and other fields.

在儲存擠塑板產品時，應注意擠塑板不能長時間暴露在陽光下。它也可以是涼爽干燥的地方。板墊也應在墻外的衣架下和擠壓板之間使用。擠塑聚苯乙烯不應靠近電和火。電和火很容易損壞擠塑聚苯乙烯。

When storing extruded board products, it shall be noted that extruded boards shall not be exposed to the sun for a long time. It can also be a cool, dry place. The pad shall also be used under the clothes hanger outside the wall and between the extrusion plates. Extruded polystyrene should not be close to electricity and fire. Electricity and fire can easily damage extruded polystyrene.

山東擠塑板廠家提醒您，當室內非常潮濕時，擠塑板的內表面可能會暴露出來，因此應在基墻上涂抹防潮層，例如單組份聚氨酯防水涂料或單組份丙烯酸防水涂料。采用防水保溫一體的保溫材料，如現場噴涂硬質聚氨酯泡沫塑料。對于砌塊保溫材料，盡量選擇吸水率低的材料。

Shandong extruded board manufacturer reminds you that when the room is very wet, the inner surface of the extruded board may be exposed, so you should apply a damp proof layer on the foundation wall, such as one component polyurethane waterproof coating or one component acrylic waterproof coating. Adopt waterproof and thermal insulation materials, such as hard polyurethane foam sprayed on site. For block insulation materials, try to select materials with low water absorption.

以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注我們網站http://www.45aap.com并咨詢我們的工作人員，將竭誠為您服務。

The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.45aap.com And consult our staff, will serve you wholeheartedly.